You have no items in your shopping cart.

Blog

Woodworking Router Tips

Monday, July 10, 2017 Comments (0)

One of the most versatile tools you will find in any woodworking shop is the router. The router is used to trim, edge, detail, drill and hollow out different areas of wood. The uses of a router are only limited by the type of router bit you are using, and by your innovative ! Relying on the router bit you choose, you'll be able to completely change the uses of this useful tool. Woodworking with a router is an important talent to learn. Listed below are a few tips for you so you should utilize your router well.

Woodworking Router - Tip number One

Think about how you'll be hanging onto the wood router whereas it's cutting. Are the handles comfortable enough for steady use? Do the shape and materials of the handles will let you management the wood router correctly? A few of these woodworking tools are also obtainable with "D" handles (at extra cost) which can give you higher management and feel. One wooden router from Milwaukee even affords a padded grip around the exterior of the router base. One hand goes on the rubber grip whereas the other goes on a standard knob.

Woodworking Router - Tip number Two

Router bits appear in three shank sizes, one-quarter inch, three-eighths inch and one-half inch. The half-inch shank bits are only a little more pricey than the quarter-inch ones and yet, they will give you a distinct advantage. With a larger diameter shank and a bigger diameter collet, the chance is much less of slippage under heavy loads. Consider buying just half-inch shank bits, especially if you are spinning big cutters.

Woodworking Router - Tip number Three

Put on eye protection, gloves and a breathing mask. Run your router in a counter clockwise direction around the wooden stock, across the grain on either end of the board first and then slicing with the grain. Always move your router so it is cutting into the wood in the opposite direction of the spinning bit.

Woodworking Router - Tip number Four

Double check to make sure you're using the right bit for the type of cut you wish to make. Be very cautious when handling a bit by the sharp end and always be sure you are wearing protecting gloves so you do not harm yourself. As soon as you start using your router, you will start to see the entire various things that you'll do with it. It's such a flexible tool, and for a lot of woodworkers, it's their favourite device in the workshop. Select a router that is best for you, and you'll quickly uncover that it is one of your favorite tools too!

For replacement parts go to www.Parts.TroyOnlineSales.com

Read Full Post

Bosch Power Tools

Friday, July 07, 2017 Comments (0)

Bosch has released newer variants of their vastly well-liked and best selling 4000 series table saws. The newer versions of the table saws is the Bosch 4100 table saw series. This new series has three different models.

They are as follows:

1. The Bosch 4100 table saw - standard base unit that does not include the Gravity Rise Stand. This unit will be bought if portability is not an issue or you would like to mount this unit on a bench or stand you already own.

2. The Bosch 4100 09 table saw. This is the second unit in the series and incorporates Bosch's award winning Gravity Rise Stand. If portability is wanted then this model is an excellent acquisition.

3. The top of the range in the series is the Bosch 4100dg table saw. This unit includes the Gravity Rise stand plus Digital Squarelock Rip fence. If greatest precision plus portability is required then this unit is what you are searching for.

All of the above models however have the base technology of the Bosch 4100 table saw series. Let us have a short run through of what the newer technology features above the older 4000 series models.

� To begin with all the models in the new 4100 series comes with the latest Smart Guard System. This technology presents maximum safety with a tool free modular blade guard, anti-kickback pawls & riving knife. As mentioned there are no tools required whatsoever to take off or attach any of these features making it really user friendly. Plus the newly designed blade guard works separately with one another to provide better control and safety whilst cutting.

Secondly every one of of the models apart from the 4100dg incorporate the Squarelock Rip fence. This fence has been designed and built for utmost trueness and it glides with ease along the rail and will firmly lock into place where needed to. This decisive locking mechanism allows great consistent precise cutting. The 4100dg on the other hand comes with the digital version of this to gain the ultimate in precision cutting.

� All of the models boast a generous machined aluminium table top. They are actually the leading in the range with dimensions of 29inches by 21.5 inches. This superior work surface will allow you to be able to rip larger stock or timber a lot faster and easier. The table has side extensions and if added supports are considered necessary one can easily buy a rear or side extension support for the Bosch 4100 table saw range.

� An added patented feature or technology, I should say, is the Constant Response Circuitry that is applied in the Bosch 4100 table saws. This technology screens the power output of the motor and directly increases the torque of the motor when needed to maintain a unvarying power output when cutting. Still under intense load cutting the motor's power remains steady and smooth. The Soft Start technology, another attribute, enables the unit to run quieter than most other table saws as well.

� Last but not least, and a feature that impresses many, is that every one of the accessories such as the Smart Guard System, Fence, Miter Gauge and push stick store neatly and securly on the base of the unit. It even has a storage place for extra saw blades. Pretty handy.

To summarise the Bosch 4100 table saw series is the upgraded form of the top selling 4000 series and it is already proving to be a winner amongst the trade. There are loads of favorable comments for the Bosch 4100 table saw. Here are one or 2 of the customer comments:

"Great saw!, April 20, 2010
By P. Novak"

This review is from: Bosch 4100 10-Inch Worksite Table Saw.
"This is the first table saw I have owned, although I have used a really old Shopsmith. This saw is a delight to use. Assembly took about 10 minutes which really involved finding and removing all of the packing supplies, and adding the safety devices. The blade was square on arrival. All of the components were there, and survived delivery with no trauma. I've cut 3/4 and 1/4 birch plywood, and poplar hardwood so far, with no concerns. The tearout was minimum, a great deal less than I anticipated. The saw has all of the safety features, blade guard, splitter, and anti-kickback fingers. I saw that the anti-kickback feature certainly works, a piece of plywood I was cutting lifted a little while cutting. There is a dust port in the rear that I hooked my shopvac to, it takes care of nearly all of the dust, but there will be some beneath the unit after cutting. The noise level wasn't unpleasant, louder than a drill press, less than a circular saw."

Fantastic quality of construction
By A. Jones (Portland, Oregon)

This review is from: Bosch 4100 10-Inch Worksite Table Saw
"This is my first table saw. Or rather it is my third because I had to return the first two. I required something to redo my interior trim and then to have around for forthcoming projects. My first two efforts were a $130 Harbor Freight cheapo (fence not precise and just in general a inadequate design) and a SKIL 3400 which is apparently a $200 saw but the design/quality of the blade guard/antikickbacks was poor and impossible to adjust to blade. I understand now why a good number are forced to run the saw with these features removed. Following this occurrence I went to the local big box store which had the Bosch and Hitachi so I could examine in person. The fence on the $225 Hitachi would go out of square when tightened. I was blown away by the quality of the Bosch and I required a saw with safety features that I wasn't going to be forced to remove.

I acquired this saw from Amazon in 2 days via Prime. I've no idea how much it cost them as it's HEAVY. I opted for the saw not including the gravity stand as I'm short on space. The other saws I tried I could carry around myself easily. The Bosch requires 2 people. I can barely pick it up, it is that sturdy. Heavy is good in terms of accurateness when the saw is running. If you have to to move it around solo you will need the gravity stand. I may end up buying it.

The quality of the unit and fit and finish is simply top-notch. If you welcome things that are well made and well designed, this is the saw for you. It arrives with a quick install guide. Reading this I had the riving knife, guard assembly and anti-kickbacks installed first time in under 5 minutes, no adjustment required, everything is just correct. How amazing is that? Now I know how it works, it's 30 second job to remove/reinstall them. In addition the blade guard is a completely different design that just works.

The fence is fabulous also. Smooth sliding and does not lose accuracy when you fasten it down.

It's a $400 saw, you can get less costly ones for sure but this product redefines the saying you get what you pay for".

Here's a great resource for tool parts ... www.parts.troyonlinesales.com

Read Full Post

Painting Ideas

Tuesday, July 04, 2017 Comments (0)

Painting Ideas

Often getting the painting began does not start with the paint. Depending on the paint color you are preparing to utilize a coat of guide can actually assist with the application of the paint. Utilizing a coat of guide on the walls when you are preparing to paint them purple or red can conserve you 2 or 3 coats when it comes time to put the color on the wall.



It can be extremely appealing to glop on a great deal of paint in one open area simply to see exactly what the color will appear like when it is done, however prevent this temptation and paint in good thin even strokes. When you glop a lot on, it is tough to even it out and typically the preliminary test area will constantly appear darker on the completed wall, so if you prepare to do this, ensure you have a great photo to hang up on the wall to cover the area. If you are utilizing a brush, capture any drips rapidly so that they do not dry as rough streaks and if you are utilizing a roller, roll the paint in lots of instructions so there is no apparent stop and begin marks in the paint once it dries.

Absolutely nothing improves a dull space like a coat of paint. Whether you are lightening up drab walls by painting them white or including a significant splash of color, paint is the least pricey method to make an obvious ornamental modification in your house. Keep in mind these useful suggestions and techniques to assist you get the task done if you are preparing to paint a space quickly.



There is a lot of work to do prior to you get to the enjoyable part of including colors on the walls when you set out to paint. The prep work can appear laborious, however you must never ever avoid it, since if you prep your space properly the painting will go much faster and completion outcomes will be far better.



Whether you are lightening up drab walls by painting them white or including a significant splash of color, paint is the least pricey method to make a visible ornamental modification in your house. If you are painting your space a dark color such as deep red or navy blue, you may require more paint than if you were painting the space white. Depending on the paint color you are preparing to utilize a coat of guide can actually assist with the application of the paint. It can be extremely appealing to glop on a lot of paint in one open area simply to see exactly what the color will look like when it is done, however prevent this temptation and paint in great thin even strokes. In some cases if you wait till the paint is dry pieces of paint can flake off with the tape.

If the walls require to be sanded or there are repair works that require to be done, make sure you do that prior to you clean up the walls, so that you remove any dust that may interfere with your paint. As soon as the walls are fixed and cleaned up, tape off any locations that you do not desire paint on. Blue painters tape works best, since it comes off simple and does not eliminate the paint you simply included to your walls.



If you are painting your space a dark color such as deep red or navy blue, you may require more paint than if you were painting the space white. These colors tend to soak into the walls and frequently require more than one coat to attain the depth of the color on the paint sample. You may be lured to utilize an old sheet, however this isn't truly an excellent alternative for a genuine drop fabric since if you spill paint it can bleed right through a fabric sheet and destroy your carpet.

It is a great concept to thoroughly get rid of the tape while the paint is still a little damp as soon as you are done painting and you aren't preparing to include any longer coats. Often if you wait till the paint is dry pieces of paint can exfoliate with the tape. Wait a day or 2 prior to you move any furnishings back into the space, simply to make sure whatever is entirely dry

Read Full Post

Wood Working Equipment

Tuesday, July 04, 2017 Comments (0)

Wood Working Equipment

Planer jointer is wood working equipment utilized for flattening and smoothing of the work piece. It has blades that turn in the horizontal instructions. It likewise has directing fence, which will help with to provide the work piece, a 90-degree cut.

Spindle molder is the equipment utilized for bigger work. If it is integrated with the feeding maker, it will be one of the most beneficial wood working equipment.



Band saw is another type of wood working equipment. A band saw typically has a fence which guides the wood so that it can be cut as preferred. It has a 'cross can cut bar' as well, which permits cross cuts.

Thicknesser is utilized for cutting the wood to supply it a consistent density. This can be done by smoothening of the wood piece with its aid. It is not beneficial for making the work piece flat.

Fixed drill press as the name recommends is a drilling maker. The fixed drilling makers help with to make holes that are more precise.



Today we have the choice of utilizing wood working equipment. Some of the typical wood working equipment is table saw, planer, drilling maker and spindle molder. The table saws can be called as the most beneficial of the wood working equipment. Planer jointer is wood working equipment utilized for flattening and smoothing of the work piece. If it is integrated with the feeding device, it will be one of the most helpful wood working equipment.

On the other hand, the moving table saw slides over the table on which it is installed. We can cut a wood piece put it. It is extremely commonly utilized for cutting flat panels of wood.

These are a few of the wood working equipment offered nowadays. Continuous enhancements are occurring and for this reason the capabilities, along with the functions of these makers, are enhancing.



A few of the typical wood working equipment is table saw, planer, drilling device and spindle molder. There is a great deal of range offered for the size and capability of these devices. They can be picked inning accordance with the task for which we wish to utilize them.

In the earlier days, wood working was done with the tools that had to be by hand run. Today we have the choice of utilizing wood working equipment.

The table saws can be called as the most helpful of the wood working equipment. There are 2 types of wood saws offered. In addition, a fence, which guides the wood for cutting, is connected to the exact same side.

Read Full Post

Comparing DeWalt and Makita Table Saws

Tuesday, July 04, 2017 Comments (0)

Visit any job site and you're likely to see at least one miter saw being used at any given moment. More often than not, it will be a bright yellow saw. Because DeWalt is, without a doubt, the most popular brand among contractors.

 

Did you ever ask yourself why that is? Is it because they're the only ones that can do the job? Or is it the best brand out there?

 

The answers to these questions is a definite no. But it's unlikely that a guy who spent $600-700 on a miter saw is going to tell someone else it's not the best. So anyone who asked him about it goes and buys one.

 

Just so you know there could be a better alternative to the DeWalt, let's look at Makita's new generation of sliding compound miters, the 12" LS1216L and the 10" LS1016L.

- Makita includes a built-in, independent laser so you can set up your cut before actually turning on the saw (not so with DeWalt, theirs is an extra cost add-on)

- The LS1216L can handle crown molding up to 8" nested vertically (compared to 6-5/8" on the 12" DeWalt DW718) and baseboard up to 6-1/2"

- The LS1016L can handle crown molding up to 6-5/8" and baseboard up to 4-3/4" vertically

- Both models of Makita have an electronically controlled 15 amp motor so the speed is constant, even under load

- Cross cutting at 90 degrees the 12" LS1216L will handle up to 15" and the 10" LS1016L up to 12"

- Both models have split, sliding fences. Top and bottom portions both slide independently to increase control, precision and support while giving you clearance for bevel cuts

- The sliding system uses four round rails riding on ball bearings to keep the movement smooth and rigid, while saving space

- Both Makita models have 9 positive miter stops and 7 bevel stops

- You get more features and cutting capacity with the Makita LS1216L for about the same price as the DeWalt DW718 Makita LS1016L and LS1216L dual bevel slide compound miter saws are built with typical Makita quality, durability and ease of use.

"Best saw I've ever used" is what one owner of a Makita miter saw said. Another buyer said that after using a Makita miter saw, he switched all his power tools to Makita. Hmm, not a bad idea.{Other Makita Saws} For replacement parts have a look at www.Parts.TroyOnlineSales.com

Read Full Post

Bosch Power Tools

Wednesday, May 24, 2017 Comments (0)

Bosch Power Tools

Bosch offers consumers something not many other power tool manufacturers have. With many of their power tools including saws and drills, you get to choose the maximum power and the minimum weight you want from that particular power tool.

Bosch power tools offers the consumer a full line of both cord and cordless power tools. In addition to the basic power tools that are offered including saws, drills, routers, sanders, nailers, power screwdrivers; Bosch offers some great specialty tools.



You will also get a great drop light and a heavy duty bag to carry it all in. As if that wasn't enough you will also get two battery chargers, a drill bit holder, various saw blades, and two extra batteries. This power tool kit has everything you need to complete a variety of home improvement products at a price of about $500.

You can purchase Bosch power tools at most hardware stores and home improvement stores including Ace Hardware and Home Depot.

Bosch offers consumers something not many other power tool manufacturers have. It is called the Flexible Power System. With many of their power tools including saws and drills, you get to choose the maximum power and the minimum weight you want from that particular power tool.



Are you in the market for several power tools? One of the best selling products offered by Bosch is the five Pak. This is an 18 volt cordless tool kit.

Bosch power tools offers the consumer a full line of both cord and cordless power tools. They offer a large selection of power tools as well as accessories. In addition to the basic power tools that are offered including saws, drills, routers, sanders, nailers, power screwdrivers; Bosch offers some great specialty tools.



If you need repairs to a Bosch power tool, contact them directly. They work with service providers all over the world who will repair your Bosch power tool quickly and effectively.

Bosch takes customer satisfaction very seriously. Bosch understands that down time with your tools affects your productivity. All Bosch power tools are guaranteed to be free from defects.

The Bosch heat gun offers several temperatures as well as two speeds. You can get a Bosh heat gun in several sizes. The Bosch foam rubber cutter is an excellent specialty tool that is designed to easily cut through foam rubber and flexible foams.



You can purchase Bosch power tools at most hardware stores and home improvement stores including Ace Hardware and Home Depot. You won't be disappointed with the power tools you purchase from the Bosch brand.

Bosch has some great new power tools on the market. The I-Driver is a power screwdriver, designed with a pivot head to get into very tight spaces. The Brute Tough drill and driver is versatile and very powerful.

If that is more than your budget can handle, consider purchasing reconditioned Bosch power tools. The Bosch website has information on the various reconditioned power tools they have available at this time.

Read Full Post

Things To Remember While Choosing Retailer

Wednesday, November 09, 2016 Comments (0)

Things To Remember While Choosing Retailer To Buy Makita Replacement Parts In British Columbia

Technology has taken a long way but it has also left us completely dependent on it. There are certain things that you will have to make sure of when you are planning to get the best of the deals in the area you need to be aware of the parts that you are replacing with the original ones. You will have to make sure that you are choosing the best company that can make the most of the deals. There are many motor companies that promise replacement of the damaged product with the original one but always end up giving something that isn’t original whatsoever. You will have to make sure that you are choosing the best one in the area. Makita replacement parts in British Columbia is available in many areas, but you will have to make sure that you are choosing the best retailer that promises to sell the best parts and have experienced people to get the replacement installation done.

There are certain factors that make the buying of Makita replacement parts in British Columbia even more helpful:

  1.        The quality of the service that the retailer has been providing over the years
  2.        The authentic paper that they offer to you
  3.        Check and recheck the authenticity of the retailer for the original Makita parts or tools
  4.        Make sure that you check the retailer's license as well

 You will have to make sure that you are choosing the best of the deals in the area. There are certain things that you will have to make sure of when you are choosing the best Milwaukee tools parts, British Columbia. Like Makita, this is also a very popular brand when it comes to getting the best replacement or a new tool for your house.

To conclude, it can be said that there are certain things that you will have to make sure of when you are planning to get the best of the deals in the area. You will have to make sure that you are either choosing Makita or Milwaukee tools parts in British Columbia so that you can make the choices even more guaranteed and ensure that no matter what the parts or the tools will always be better than any other. Therefore, you will have to make sure that you choose the best of the deals in the area when you are looking for the best retailer that provides the quality tools that offers proper longevity.

S: Technology has taken a long way but it has also left us completely dependent on it. There are certain things that you will have to make sure of when you are planning to get the best of the deals in the area you need to be aware of the parts that you are replacing with the original ones. Read on to know more about Makita replacement parts in British Columbia.

Read Full Post

Purchasing Drill Parts

Wednesday, November 09, 2016 Comments (0)

Purchasing Drill Parts in Vancouver British Columbia

In the contemporary times, there are numerous types of a drilling machine that has its own quality different from another one. On the other hand, choosing the right one can be a difficult task unless you are aware of which drill is better for fulfilling your purpose. In case, you are on the verge of buying a drilling machine then make sure that you are quite sure about buying a particular one but if you are not sure then you must study a little bit as well as research about the place from where you are buying your drilling machine.

In such case, the following given points will help you to choose the right drill parts in Vancouver British Columbia and find a place that is reputed for selling drilling machine.

Buying the perfect and quality drilling machine from the right place

  •          If has to be sure whether the kind of work for which you need a drilling machine. The truth is that though drills are primarily used make holes but they also have lots of other functions that come along with it. The extra function that comes along with a drilling machine may be hammer action, gears as well as variable speeds for the best result that an owner seeks for his need.

 

  •          There is also a huge range of drilling machine so that people can find the right tool for their particular need and use. After you have decided the kind of drill that you seek for your need then it is time to find the right company that sells your drill model with great build quality and comes with the best value for money.

 

  •          In case, you need drilling machine for tougher tasks then you must consider the facts like the features of a drill like combination drills, drill drivers, as well as percussion drills so that you can use it according to your advantages. In that case, before buying Drill Parts in Vancouver Island make sure what part will help you to get the perfect result that you need for your work.

 

  •          Choosing a drill is very important and if you need a drill for basic tasks then cordless drills are the best choice for you that also come with a rechargeable battery. Even though they lack the power for heavier tasks but since they are lightweight and easy to handle makes them very easy to carry at any place and use it at any time according to needs and requisites.

On a concluding note, it is very important to select the right drill part to get the right perfect result that you want while drilling a hole. However, make sure that you are buying your drilling machine or even parts of the drill from a reputed place that specializes in selling quality drilling objects.

 

Summary: the given blog helps us to understand the various ways to buy the best drill parts in Vancouver British Columbia. It also highlights the various other facts about buying a quality drill parts from a reputed shop after proper research and study. We also come to know about various other relevant facts about drilling machine from the blog given here.

 



Read Full Post

More Power Tool Replacement Parts Added

Wednesday, October 12, 2016 Comments (0)

Give Power Tools a New Ember with Power Tool Parts in North America

Power tool owners know how robustly made and capable their tools are. But after a time of extensive and demanding usage, they know that it will sooner or later break down due to normal wear and tear of its mechanism. Once this occurs, the task of seeking the correct power tool parts in North America commences. Fortunately, unlike in the past, doing this tedious task has become easier to do. Today, you can quickly access a sales and service center like Troy Online Sales, or a certified business associate with the click of your finger.

Troy Online provides replacement parts for leading manufacturers like: Black and Decker, Bosch, Bostich, Delta, Dewalt, Fein, Freud, General, Hitachi, King, Makita, Metabo, Milwaukee, Porter Cable, Rotom, and Walter.

We have breakdown drawings, pictures of the parts and parts list for all the tools you need: Circular Saws, Compressors, Drills, Grinders, Hammer Drills, Miter Saws, Multi-Tools, Nailers, Planers, Rotary Hammers, Routers, Sanders, Table Saws, Vacuums and more.

 Power Tool in Parts North America – The Search…

Searching for the right power tool parts in North America has never been easier than these days. Since our suppliers are the top global supplier of automotive and manufacturing technology and consumer goods and construction technology, it should only tag along that leads in the after sales marketing of its range of products.

These branded tool parts stand for excellence, brilliance, and terrific performance with a matchless popularity to go with. With the correct replacement parts, your DIY power tools will last longer and perform like new.  Power tool parts in North America makes all your tools function more efficiently, and because these power tools impress people not by words but by works - excellent works, unsurpassed handling, and high-tech technology, so are its power tool parts.

 prides itself extremely in taking client satisfaction seriously and makes every effort to meet all their needs to the fullest degree possible. The company knows that your work is where you make your money, and reliable, safe tools are critical to your success.

At Troy Online Sales, we do keep our customers in complete peace of mind as they know that we are the name that people trust for quality products and service assurance. So, if you are intending to give a new spark to your power tools, think of using our power tool parts in North America. We give you the opportunity to buy our branded products online.

Simply have a look at our product catalog and find your desired tool parts. We are always here to assist you in finding the right power tool parts so that your manufacturing or automotive industry keeps running without any problem.

Read Full Post

Milwaukee Tool Tracking

Monday, August 22, 2016 Comments (0)

I love this chip tracker that Milwaukee has installed in your drill, saw, etc and let's you find your power tools from your phone.

Ever lend out a tool and not get it back - yup, that's annoying.

Have a look here:

http://www.coptool.com/tool-tracking-lost-found-with-milwaukee-one-key/

Read Full Post